APC Tools & Equipment-Q2-2021

FRONT-END & SUSPENSION

Ball Joint Service Tools

Wheel Hub Service Tools

CTA-7395 $52 45

OTC-6575 $857 45

Ball Joint Hammer Nut Kit • Breaks off steering knuckle & suspension joints without damaging bolts • Services Mercedes Benz, BMW, Honda, Toyota, Lexus, Subaru and more • Also use for removal of wheel studs

Hub Grappler™Kit • For servicing wheel hubs and bearings on the vehicle without removing the steering components or knuckle • Application coverage up to 2009 model year • Includes tie rod/ball joint tool and two Ford axle installers

• Sizes: M12 x 1.25 (Honda, Subaru), M12 x 1.5 (Mercedes, Toyota), M14 x 1.5 (Mercedes, BMW, Toyota) & M16 x 1.5 (Mercedes, Toyota).

CTA-1732 $38 95

OTC-6575H P

41mm 12 Point BMW/Benz Ball Joint Impact Socket, 1/2" Drive • Applications includes BMW and Mercedes lower ball joint

Hydraulic Hub Grappler™Kit • Same as #OTC-6575 but also includes the Hydraulic Kit

AST-78620 $36 45

Subaru Ball Joint Puller • Removes seized, rusted and/or corroded bolt-in Subaru ball joints in a single pulling motion • Designed for easy use with vehicle on jack stands using a deep 24mm socket and impact, a hand wrench or any common slide hammer • For Subaru Baja 2003+, Forester 1998+, Impreza 1993+, Legacy 1990+, Outback 2000+ and more

Hub Grappler™Hydraulic Kit OTC-6575-3 $1148 95

Hub Grappler™ Puller OTC-6575-1 $273 45

Deluxe Ball Joint Service Set ATD-8696 $228 95

CAL-90703 $32 95

3/8" Drive Dodge/Ram Truck RearWheel Hub Nut Socket • Fits rear axle locknuts of Dodge/Ram trucks with six holes • Applications: models 1500-5500 from 2006-2014 (Chassis codes: D2, DC, DD, DH, DJ, DP, DR, DS) • Comparable to Mopar® factory tool #8954A

• Heavy-duty tool set is excellent for removal and installation of press-fit parts such as ball joints, universal joints, and truck brake anchor pins

ATD-8697 $202 95

CAL-977 $79 45

Add-On Ball Joint Adapter Set • Expands the serviceability of your deluxe ball joint service set (ATD-8696) • Works on most 2WD and 4WD pickups, vans and SUVs thru 2006 • Works on press-fit upper and lower ball joints

Toyota Front Hub Nut Socket • Designed to fit front hub locknuts on 2007 and up 2WD 4 Runners and Tundras, as well as 2008-2014 Sequoias • 8-pin design, with 3/4" drive • Comparable to Toyota factory tools 09318-12010 and 09602-60010

Torsion Bar Tools

ATD-8699 $440 45

21-Pc Ball Joint Master Service Kit • HD tool removes and installs ball joints, U-joints and truck brake anchor pins • Includes all of the receiver tubes and adapters for press-fit upper and lower ball joints • Works on most GM, Ford and Dodge 2WD and 4WD pickups, vans, and SUVs through 2006

AST-78823 $81 45

Late Model GMHeavy-Duty Torsion Bar Unloading Tool for 2011+ • Needed to service torsion arm and front suspension on many 2011+ full-size GM trucks • Holds the torsion bar in place while you loosen or tighten the adjusting nut • Forged alloy design with 1" hex drive bolt • Thread size: 3/4-16"

342 | April – June 2021